Infrared vs capacitive touch screen: which touch technology to choose for kiosks, signage and interactive panels

Short answer: An infrared (IR) touch screen detects a finger when it breaks a grid of invisible light beams across the screen; a projected capacitive (PCAP) touch screen detects the small electrical charge of a finger through the cover glass. As a general rule, IR suits large panels and anything touched with a pen or glove, while capacitive suits kiosks, POS terminals and mirrors where a flush, fast, sealed surface matters. This guide sets out the general differences, marked as such, and states which touch technology each of our models uses.
- Infrared touch uses a frame of light beams around the screen; capacitive touch uses a sensor grid bonded to the glass. That one difference drives the rest.
- Our interactive flat panels (55″–100″) and the queue ticket kiosk use infrared touch; our 32″ payment kiosk (10-point, 8 ms), POS terminals, vending machine, smart mirror and rotating screen use capacitive.
- As a general rule, IR works with any finger, glove or pen and stays affordable at large sizes; capacitive gives a flush, sealed surface and precise response but needs tuning for gloves and water.
- Several models let you choose: our indoor floor-standing signage and standing live-streaming machine offer IR or capacitive touch.
1. How each technology works
Infrared touch: a frame around the screen carries rows of infrared LEDs on two sides and receivers on the opposite sides. The beams form an invisible grid just above the glass; a finger or pen blocks some beams, and the controller calculates the position. The glass itself carries no sensor.
Projected capacitive touch: a transparent grid of electrodes sits on or behind the cover glass. A finger changes the electrical field at that point, and the controller reads the change through the glass. There is no frame above the surface, so the front can be completely flat.
Both support multi-touch. The rest of this comparison follows from frame versus grid.
2. Infrared vs capacitive at a glance
General characteristics of the two technologies; the exact behaviour depends on the controller, the glass and the tuning of each model.
| Factor | Infrared (IR) | Projected capacitive (PCAP) |
|---|---|---|
| Detects | Anything that blocks the beams: finger, glove, pen | A finger or a conductive stylus; gloves only if tuned |
| Surface | Raised frame around the glass | Flush, edge-to-edge glass |
| Large sizes | Scales well to 65″–100″ panels | Possible, but cost rises with size |
| Water and dirt | Drops or debris on the frame can block beams | Water on the glass can cause false touches unless tuned |
| Strong sunlight | Can interfere with the IR receivers | Not affected by light |
| Sealing | Frame makes a fully flush seal harder | Easy to seal behind one sheet of glass |
| Response | Good; can register a hover just above the glass | Precise, with no hover touches |
| Typical use | Interactive whiteboards, large signage, queue kiosks | Payment and POS terminals, mirrors, small and mid-size kiosks |
3. Which of our models use which
| Model | Touch stated in the catalog |
|---|---|
| Interactive flat panel, 55″–100″ | Infrared multi-touch, finger or stylus, anti-glare tempered glass |
| Wall-mounted interactive panel | Infrared multi-touch, finger or stylus |
| Queue ticket kiosk | Infrared touch behind explosion-proof, dust-proof tempered glass |
| Indoor floor-standing signage | Optional: infrared or 10-point capacitive |
| Standing live-streaming machine | IR or capacitive |
| 32″ payment kiosk | 10-point capacitive, 8 ms |
| Dual-screen self-service terminal | 10-point capacitive |
| 15.6″ dual-screen POS | Capacitive |
| Touch-screen vending machine | HD capacitive |
| Smart mirror | 10-point capacitive |
| Rotating portable touch screen | 10-point capacitive |
| Desktop live-streaming machine | Fully laminated capacitive |
Our touch kiosks are stated as 10-point touch; confirm the technology for your configuration when you order.
4. Where infrared is the better choice
- Large interactive panels: classrooms and meeting rooms at 65″–100″, where IR keeps the cost reasonable; see the interactive flat panel guide and interactive whiteboard vs projector.
- Pens, gloves and any object: writing with a passive pen, or users wearing gloves, as in some factories and clinics.
- Thick protective glass: IR does not read through the glass, so a thick tempered or explosion-proof front does not reduce sensitivity.
- Simple queue and information terminals indoors, like our queue ticket kiosk; the queue management guide covers the full system.
5. Where capacitive is the better choice
- Payment, ordering and POS: a flush, fast, precise surface for many short touches a day; see the payment kiosk guide, the self-ordering kiosk guide and the dual-screen POS guide.
- Sealed and easy-to-clean fronts: one sheet of glass with no frame edge for dirt to collect, which suits food service, hospitals and vending.
- Mirrors and design-led products: a smart mirror or rotating screen needs an edge-to-edge surface.
- Bright entrances and semi-outdoor spots: capacitive is not disturbed by sunlight, though the screen itself still needs enough brightness.
6. Gloves, water, sunlight and vandalism
As general guidance for public installations:
- Gloves: IR works with any glove. Capacitive needs a controller tuned for gloves, and thick gloves may still not work.
- Rain and cleaning spray: water on capacitive glass can create false touches unless the controller rejects water; on IR, drops or dirt in the frame can block beams. Plan cleaning for either.
- Direct sun: strong sunlight can disturb IR receivers. For outdoor or window positions, specify the touch with the outdoor brightness; see the outdoor signage guide.
- Impact: both sit behind tempered glass on most of our units; ask for the glass thickness of your configuration.
7. Operating system and software
Both technologies connect to the mainboard over USB and appear as a standard multi-touch device to Android and Windows, so your application does not change with the touch type. Check gestures your software needs, such as pinch zoom or palm rejection on a whiteboard. The Android vs Windows kiosk guide covers the operating system choice, and the custom mainboard guide covers board-level options.
8. How to decide
- Size: 65″ and above, especially for writing, points to IR.
- What touches it: pens or gloves point to IR; bare fingers on many short transactions point to capacitive.
- Surface: a flush, sealed, easy-clean front points to capacitive.
- Light: direct sun on the screen points away from IR.
- Budget at size: compare quotes for both where our model offers both.
The touch screen kiosk guide puts this choice in the context of a full kiosk specification, and the OEM kiosk cost breakdown shows where the touch panel sits in the price.
9. What to write in your RFQ
| Item | What to specify |
|---|---|
| Touch type | Infrared or projected capacitive, or ask us to quote both |
| Touch points | Number of simultaneous touches your software needs |
| Input | Finger only, passive pen, gloves |
| Glass | Tempered or explosion-proof, thickness, anti-glare |
| Environment | Indoor, window, semi-outdoor; cleaning method |
| Software | Operating system and gestures used |
Send it through the contact page.
Frequently asked questions
What is the difference between infrared and capacitive touch screens?
An infrared touch screen detects a finger or object that breaks a grid of light beams from a frame around the screen. A capacitive touch screen detects the electrical charge of a finger through a sensor grid on the glass, giving a flush surface without a frame.
Which is better for a self-service kiosk?
For payment, ordering and POS, capacitive is the usual choice: our 32″ payment kiosk uses 10-point capacitive touch at 8 ms. For simple indoor queue terminals and large screens, infrared works well; our queue ticket kiosk uses infrared.
Does an infrared touch screen work with gloves?
Yes. Infrared detects anything that blocks its beams, so gloves, pens and other objects work. Capacitive needs a glove-tuned controller, and thick gloves may still not register.
Why do interactive flat panels use infrared touch?
At 55″ to 100″, infrared stays affordable and works with a finger or a passive stylus for writing. Our interactive flat panels use infrared multi-touch behind anti-glare tempered glass.


